LED Strip
Light: LED
Strip LIGHT Flex is a low voltage (12 volt) Super Bright LED
lighting in a flexible ultra sleek thin PCB strip that is available in there
varieties; regular Flex strip type A, suitable for dry location
and type B,C featuring water resistance (IP
67, 68 respectively). Type
C
has a protective Silicone cover and Type B has a encapsulated
plastic Gel.
Designed for the lighting professional, this
lighting can be used for architectural lighting, sign letter
light, concealed lighting perimeter lighting and many other
applications. Available in red, green, blue, yellow and white
colors including RGB that allows you to change colors with the
optional controller (see below). LED Flex Strip Lighting is available with a
clip (Silicone Type) on or tape base (A) for easy install. The base
is flat and flexible and can be easily mount onto most flat
surfaces non-conductive surfaces. It's small size and low voltage makes this lighting
ideal for a wide range of applications. Typically it is twice as
bright as LED Rope lighting. Can be cut to size by at each 3 LED
(12V model) intervals at marking points (by electricians) and
rejoined by soldering at marked soldering points.
Applications
Border
or perimeter lighting.
Shelf light
Architectural decorative lighting .
Use
indoor and outdoors (Silicone or Gel Type only) use to
highlight areas.
Concealed
lighting
Cove and
under cabinet lighting.
Deck lighting (type C)
Features
Available in 12 or 24 volts.
Super
Bright 3528 & 5060 SMD LEDS.
Little
or no heat, low power consumption.
Can be
cut to size at marked intervals and rejoined by
electricians.
Operating temperature: -10 C ~ 40 heat C.
Long
life span of LED lights, 30,000 hours plus.
RGB
Color changing available.
Continuous length flexible LED light strips
Solid-state, high vibration resistant SMD chips.
Small & powerful LED!
Single color includes indoor type barrel connector.
Maximum length of 12VDC Ribbon Flex strip is 6 meters (197")
TYPE A: Regular LED FLEXSTRIP: PCB (Printed Circuit board) material with double sided tape. For dry
locations (INDOOR).
Easy to access solder points to rejoin.Use
only on Non-conductive surfaces such as glass or use
with the recommend channel track (see below).
TYPE B:
Like type A, except it PCB
material is encapsulated with a plastic
Gel and double sided tape.
Water resistant
coat (IP68).
TYPE C:
Like type A, except PCB material is
encapsulated
with a Silicone
cover. Water resistant
coat
(IP67) and indoor type connectector. Easy to access solder points to rejoin.
Good for indoor use without the need of track. mounts to most
surfaces.
Single
Color feature the Super Bright 3528 & 5060 3 LEDS in 1 SMD LED CHIP
Note that you need a 12 volt power supply to power
one roll of the 12 volt Flex Strip below. It is NOT included.
Notethat the connectors (power
source) for type A, B and C are for dry locations only. If FLEXSTRIP is cut or rejoined, it is no longer water resistant. Certain
electrical precautions must be taken. Maximum
length of 12VDC Ribbon Flex strip is 6 meters (197") , do
not extend.
Consulted with a licensed electrician before proceeding with
install and read all instructions enclosed in packaging.
ITEM
VOLTS
WATTS
ROLL
LEDS
COLOR
TYPE
VIEW
ANGLE
LUMINOUS FLUX/FT
L*W*H (FT)
RL
PRICE ROLL
CART
FSC-5M-300-12V-R
12VDC
24W
300
Red
C
120
40
5000*8*2
(16.4FT)
$159.00
FSC-5M-300-12V-Y
12VDC
24W
300
Yellow
C
120
40
5000*8*2
(16.4FT)
$159.00
Sold Out
FSC-5M-300-12V-B
12VDC
24W
300
Blue
C
120
55
5000*8*2(16.4FT)
$159.00
FSC-5M-300-12V-G
12VDC
24W
300
Green
C
120
58
5000*8*2(16.4FT)
$159.00
FSA-5M-300-12V-W
12VDC
24W
300
Pure White
A
120
55
5000*8*2(16.4FT)
$139.00
FSC-5M-300-12V-W
12VDC
24W
300
Pure-White
C
120
55
5000*12*4
(16.4FT)
$139.00
FSC-5M-300-12V-WW
12VDC
24W
300
Warm-White
C
120
50
5000*12*4
(16.4FT)
$149.00
Note that
you need a 12 volt power supply to power one roll of the
12 volt LED Flex Strip. It is NOT included.
RPT4012P5A:
Indoor AC/DC Adapter - 12VDC 3.3A Switching Power
Supply. Lightweight, compact desktop switching power
supply for indoor use. Features a universal input
voltage of 100-240VAC 50/60Hz and includes a barrel type
(coaxial) output connector as indicated. Can power
one roll (6 meters max) of LED Flex
strip single color or 5 meters of RGB Ribbon Flex Strip.. Not dimmable.
For dimming options, please see here.
$45.00
RPT6012P5A3:
Indoor AC/DC Adapter - 12VDC 5A Switching Power Supply.
Lightweight, compact desktop switching power supply for
indoor use. Features a universal input voltage of
100-240VAC 50/60Hz and includes a barrel type (coaxial)
output connector as indicated. Can power two
roll (5 meters max) of single color LED Flex strip. For
RGB Flex Ribbon, you can power one roll (6 meters max). Not dimmable.
For dimming options, please see here.
$60.00
COLOR CHANGINGRGB
RIBBON LIGHT
(5060) 3 LED (RED,
GREEN, BLUE) INSIDE OF EACH LED
Mixing of color requires a
Color
RGB
controller (below). With the optional
controller, you can make the RGB Ribbon light change to many
different colors, including slow glow color fading one to
another, brightness levels, faux white and more...
LT-3600RC RGB LOW VOLTAGE LED
CONTROLLER (RGB color changer): Controller
is
used to change colors of the RGB Flex Strip and can be
used to control other low voltage RGB LED lighting.
Changes LED lighting gradually or in a pattern from
white, green, blue, red, orange, cyan and many more. Maximum voltage 24 volts &
maximum amps is 6 total.
Specification: Working Temperature: -10 to
40 degrees Celsius
MAX In/output Voltage: 12VDC OR 24VDC
Dimension: 8.5" X 1.5" X 1.5"
Connecting Mode: Common anode Remote control
Max Current:2A for each color
Working current: 6 amps.
For Indoor use.
$98.00
HL LOW VOLTAGE DATA REPEATER:
The Data repeater is used in combination
with the RGB LED controller to repeat the signal coming
from the RGB controller. Required every 20 feet. With
this repeater you can extend the LED RGB lighting and
have color changing effect continue. Maximum
voltage 12 volts & maximum amps is 6.
Specification:
Working Temperature: -10 to
40 degrees Celsius
MAX In/output Voltage: 12VDC VDC
Dimension: 4.6" x 2.5" x 1" (12cmx6.5cmx2.5cm)
Connecting Mode: Common anode
Max Current:3A for each color
Working current: 6 amps.
For Indoor use.
Channel track allows you to to create
straight perimeter outlines on most surfaces while protection
the Flex Strip. Channel is a plastic material that can be easily
attached to most surfaces such as wood, metal and brick. After
the channel is in place and installed, simply peel off the
adhesive backing from Flex Strip and install into the track. Not
required for LED Flex Strip model with Silicone jacket or type
B. Comes in 3 foot (36" x 5/8" x 3/8") long pieces that can be
cut to size ($3.89 ea).
Install
fuse between power supply and Flex Strip Lighting to avoid
damage or hazards.
This product is for industrial use only for installation by
locally licensed electricians, engineers and electrical
professionals. Advance wiring and soldering skills required.
Sold in rolls only. Prices in USD. Specifications subject to
change without notice. Note: 1 inch = 25.4mm. Not for mission
critical mission or aircraft use.
Technical Data:
Standard Length:
5 & 6 Meters per Reel
Printed Circuit
Board Width: 8mm for Single Color (12mm for Silicone), 10mm
for RGB Color excluding covering.
Printed Circuit Board thickness:
0.2-0.25mm.
Working Voltage: 12VDC
3 LEDs
each as one series.
Maximum working
Current: 2A for Single Color at 5 meters, 3.3 amps at 6
meters.
Caution:
Connection soldering can be only
made on selected soldering area.
Max. soldering temperature can not
exceed 260 Celsius degree for a max of 10 seconds.
The Min. bending radius is 2cm. The
light and all its components can not be mechanically
pressed.
During installation, do not damage
the printed circuit.
Only qualified electrician or
engineer can perform installation. Correct polarity is
imperative.
Parallel connection only.
Keep away from flammable materials and
fire.
Safety fuse is required for each roll
before connection to power source.
When install on conductive surface,
needs isolation point between light and surface.
Damage from corrosion is NOT
subject to material defect claims.
Voltage must not exceed 12VDC and
must be regulated.
Tape may damage surface when
removing.
Do not cross
PCB strip or power on when in a roll (it will damage the
LEDS). Roll out completely straight before applying power.
For professional and commercial use
only.
Maximum length is
5 meters (16.4 feet), for 3528 SMD and 6 meters for 5060 SMD.
Do NOT exceed.
Never power when on reel.
Static
electricity will damage LEDS!
Install using Channel Track for type A.
Flex Strip must be protected after install by a
non-conductive surface.
LED FLEX
STRIP LIGHTING:
is for commercial use and sale only. Qualified trades people
that are familiar and knowledgeable with general construction
and electrical installation techniques should only do the
installation. Licensed electricians should provide all
installation and hook-up of both the primary input and secondary
outputs of the Power Supply. All installation and hook-up should
be done in accordance with all national and local codes.
Transformers that may be required should be provided by the
licensed electrician in accordance electrical codes and laws.
Specification:
