1-800-387-4081
902 MHz – Self-powered Wireless Light Switches are powered by EnOcean technology that converts the press of the switch into a small amount of electricity.
This electricity is used to transmit a wireless signal that communicates with a wide variety of ILLUMRA Receivers.
Battery-free wireless light switches are primarily used to control lights in homes or businesses but they can be used to control virtually any on/off device. Each Self-powered Wireless Light Switch can be placed anywhere within range of a receiver. Traditionally the wireless light switch is surface mounted on a wall with screws or industrial tape but can also be used in a standard switch box or as a wireless hand-held remote.
Pairing Wireless Switch and Receiver
1) Press LNK button on 902MHz Receiver for 0.5 seconds
2) LED Lights will start to Blink
3) On 902MHz wireless switch press the Top of the Rocker Button once
4) Wait for 30 seconds or Press LNK button on 902MHz for 2 seconds. If LED light stop blinking, both Switch and Receiver are paired and ready to use.
5) Press CLR button to reset pairing and start all over again.
Product Description
902 MHz – Self-powered Wireless Light Switches are powered by EnOcean technology that converts the press of the switch into a small amount of electricity.
This electricity is used to transmit a wireless signal that communicates with a wide variety of ILLUMRA Receivers.
Battery-free wireless light switches are primarily used to control lights in homes or businesses but they can be used to control virtually any on/off device. Each Self-powered Wireless Light Switch can be placed anywhere within range of a receiver. Traditionally the wireless light switch is surface mounted on a wall with screws or industrial tape but can also be used in a standard switch box or as a wireless hand-held remote.
Pairing Wireless Switch and Receiver
1) Press LNK button on 902MHz Receiver for 0.5 seconds
2) LED Lights will start to Blink
3) On 902MHz wireless switch press the Top of the Rocker Button once
4) Wait for 30 seconds or Press LNK button on 902MHz for 2 seconds. If LED light stop blinking, both Switch and Receiver are paired and ready to use.
5) Press CLR button to reset pairing and start all over again.
Technical Specifications
| Range | 50-150 feet |
| Frequency | 902 MHz |
| Power Supply | Self generated |
| Buttons | 2 Buttons (1 Rocker) |
| Output Channels | Only limited by number of receivers in range |
| Dimensions | 2.75(L) x 4.5(H) x 0.75(D) inches |
| Operation Temprature | -25 C~ 65 C (13F ~ 149F) |
| Radio Certifications | FCC (US) & IC (Canada) |
| Addressing | Factory set unique ID (1 of 4 billion) |
Wireless LED Dimming
Product Accessories
3 Wire Plug-in Relay Receiver 902MHz E9X-R12-3HOTP
The 3-wire Relay Receiver controls one light or group of lights when connected between an electrical load and a power source. One receiver can respond to up to 30 wireless remote light switches or sensors.
Wireless Dimmer Receiver 902MHz E9X-D02FL
Constant Voltage LED Dimmer with flying leads – 8-28VDC, PWM (receives 902 MHz)
Product Description
902 MHz – Self-powered Wireless Light Switches are powered by EnOcean technology that converts the press of the switch into a small amount of electricity.
This electricity is used to transmit a wireless signal that communicates with a wide variety of ILLUMRA Receivers.
Battery-free wireless light switches are primarily used to control lights in homes or businesses but they can be used to control virtually any on/off device. Each Self-powered Wireless Light Switch can be placed anywhere within range of a receiver. Traditionally the wireless light switch is surface mounted on a wall with screws or industrial tape but can also be used in a standard switch box or as a wireless hand-held remote.
Pairing Wireless Switch and Receiver
1) Press LNK button on 902MHz Receiver for 0.5 seconds
2) LED Lights will start to Blink
3) On 902MHz wireless switch press the Top of the Rocker Button once
4) Wait for 30 seconds or Press LNK button on 902MHz for 2 seconds. If LED light stop blinking, both Switch and Receiver are paired and ready to use.
5) Press CLR button to reset pairing and start all over again.
Technical Specifications
| Range | 50-150 feet |
| Frequency | 902 MHz |
| Power Supply | Self generated |
| Buttons | 2 Buttons (1 Rocker) |
| Output Channels | Only limited by number of receivers in range |
| Dimensions | 2.75(L) x 4.5(H) x 0.75(D) inches |
| Operation Temprature | -25 C~ 65 C (13F ~ 149F) |
| Radio Certifications | FCC (US) & IC (Canada) |
| Addressing | Factory set unique ID (1 of 4 billion) |
Wireless LED Dimming
Product Accessories
3 Wire Plug-in Relay Receiver 902MHz E9X-R12-3HOTP
The 3-wire Relay Receiver controls one light or group of lights when connected between an electrical load and a power source. One receiver can respond to up to 30 wireless remote light switches or sensors.
Wireless Dimmer Receiver 902MHz E9X-D02FL
Constant Voltage LED Dimmer with flying leads – 8-28VDC, PWM (receives 902 MHz)
Reviews
There are no reviews yet.
Reviews
There are no reviews yet.